JSB SPEAKER STUDIO
Scan-Speak 11M/4631G05NO PHOTONo photo available

Scan-Speak

Scan-Speak 11M/4631G05

Speaker driver · 4.33″ · —

Scan-Speak 11M/4631G05: Speaker driver. Published Fs 68 Hz, Qts 0.31 , Vas 2.7 L. Explore these values before choosing an enclosure.

Resonance Fs
68 Hz
Nominal sensitivity
90 dB
Rated power
—
Excursion Xmax
—
Design with this driver Manufacturer / original source ↗

What this driver's data tells us

Scan-Speak 11M/4631G05

Scan-Speak 11M/4631G05 is a Speaker driver. Its available data describe the following design trade-offs.

With Fs 68 Hz, Qts 0.31 and Vas 2.7 L, an ideal maximally flat sealed reference (Qtc 0.707) is approximately 0.6 L, with a −3 dB cutoff of 155.1 Hz.

This reference is compact (up to 10 L); judge its usefulness together with the cutoff above.

The calculated sealed cutoff exceeds 90 Hz. This reference is better viewed as a satellite or midbass starting point than a deep-bass solution.

Qts 0.31 makes a vented alignment worth simulating. Choose volume and tuning together and check excursion; Qts alone cannot guarantee a good result.

Published sensitivity is 90 dB, but its input/distance reference is unconfirmed. A high/low comparison with other drivers would be unreliable.

Basis and further reading

Calculated from published parameters; this is not a listening review. Box sizes are net acoustic volume for one driver. Room gain, EQ, damping material and construction losses are excluded.

Voltage-to-power conversion uses nominal impedance. These size, cutoff and sensitivity bands are editorial guides, not audio-quality standards.

Driver character card

Explore the stats

These bars show physical quantities, not sound-quality scores. A longer bar is not always better. Open a stat to learn what it means.

Resonance · Fs68 HzDisplay range: 10–2,000 Hz · log

The driver's free-air resonance. A lower value can help a bass design, but the enclosure, excursion and response determine usable bass. It is not the finished speaker's bass cutoff.

Sensitivity90 dBDisplay range: 65–115 dB

Output at the manufacturer's stated input and distance. 1 W and 2.83 V are different references for many impedances. This card keeps the original value and reference; it is not an efficiency or sound-quality rating.

Resonance damping · Qts0.31 Display range: 0–1.5

Electrical and mechanical damping combined. Lower values indicate stronger damping at resonance. It helps choose an enclosure alignment, but does not tell you whether the sound is fast, warm or detailed.

Suspension compliance · Vas2.7 LDisplay range: 0.1–1,000 L · log

The volume of air with the same compliance as the suspension. It is not a recommended box volume. Use it together with Fs and Qts.

Linear excursion · XmaxNot recordedDisplay range: 0–30 mm

Published linear excursion. Definitions differ between manufacturers; verify one-way versus peak-to-peak values. It does not by itself predict distortion or maximum safe output.

Radiating area · Sd50 cm²Display range: 1–1,500 cm² · log

Effective radiating area, not the frame's outside diameter. It helps estimate how much air a cone moves when combined with excursion.

Sensitivity reference: Nominal (reference unverified)

Which enclosure could work?

Screening guidance from the available parameters, not a guarantee. A manufacturer's exact-model enclosure plan takes priority. Listening quality cannot be ranked from T/S parameters.

Sealed

Worth trying

Fs, Qts and Vas allow a sealed-box calculation. Qts is below 0.707, so a Qtc 0.707 target may be explored; actual size and output limits still matter.

Fs 68 Hz · Qts 0.31 · Vas 2.7 L

Bass reflex

Worth trying

Qts lies in a commonly explored low-to-moderate range. Try box volume and tuning together, and check the response, port speed and cone excursion below tuning.

Fs 68 Hz · Qts 0.31 · Vas 2.7 L

Transmission line / quarter-wave

Needs careful design

Fs helps set a starting length, but taper, area, driver position and damping determine the result. There is no universal Qts pass/fail rule.

Fs 68 Hz · Qts 0.31

Back-loaded horn

Needs careful design

Use an exact-model manufacturer plan or a dedicated horn model. Qts alone cannot establish suitability. Throat, mouth, path and rear chamber must be designed together; this page does not simulate horns.

Fs 68 Hz · Qts 0.31
Explore other enclosure types

Mass-loaded transmission line

Needs careful design

The line and outlet act together. Tube length, area, damping and port mass require a coupled model; a bass-reflex preset is not an MLTL design.

Fs 68 Hz · Qts 0.31

Passive radiator system

Needs careful design

Potentially useful when a practical port is difficult, but the passive radiator's area, mass, compliance and excursion must be matched separately.

Fs 68 Hz · Qts 0.31

Double bass reflex

Needs careful design

Two chambers and two ducts interact. Check their combined resonances with the dedicated model; these parameters alone do not establish an advantage over bass reflex.

Fs 68 Hz · Qts 0.31

Open baffle

Needs careful design

Front and rear bass cancel without an enclosure. Panel size, equalization and excursion matter. Low Qts is not an automatic rejection when EQ is available.

Fs 68 Hz · Qts 0.31
Basis and further reading

Bass mini-lab

Move the volume slider. Both curves use the same box volume; the bass-reflex tuning is adjustable.

The mini-lab needs valid Fs, Qts and Vas for a bass driver. It stays unavailable when those inputs are missing or the driver has another role.

Frequency response Response

Common scale for all drivers: 20–20,000 Hz

No usable response data is recorded

Unavailable response data is not guessed or plotted.

What do published reviews say?

Attributed summaries, not our listening test or a consensus score. The enclosure, crossover, room and listening level affect each review. Exact model and impedance are checked.

No exact-model listening review has been verified for this page yet. We do not infer tonal quality from T/S parameters or borrow reviews of similar model names.

Compare prices

Compare in USD, EUR or JPY. Prices exclude shipping.

More from this manufacturer

Scan-Speak — view all →